project honda civic turbo

Project aan het bouwen? Plaats hier je updates

Re: project honda civic turbo

Berichtdoor cupra3382 » 12 Apr 2014, 23:44

ik heb een vraagje hoeveel toeren kunnen de kleppenset van supertech aan?.

cupra3382
HCN Regular
HCN Regular
 
Berichten: 137
Geregistreerd:
28 Jul 2011, 00:20
Woonplaats:
Maastricht

Re: project honda civic turbo

Berichtdoor devers » 13 Apr 2014, 07:00

cupra3382 schreef:ik heb een vraagje hoeveel toeren kunnen de kleppenset van supertech aan?.


Q: What is the difference between the Black Nitride valves and the Inconel valves? Can the inconel valves be used on the intake side?

A: The black nitride valves are stainless steel valves, with a black treatment that hardens the valves. The Inconel valves are made from a Nimonic 751 alloy which has better resistance to heat then the stainless steel. The Inconel valves are only used on the exhaust side, it is the only side that it is needed to use a higher temperature alloy.

----
Q: When should Inconel valves be used, over Black Nitride valves?

A: Inconel valves should be used, when an engine yield more then 250Hp

----


Q: Can custom valves be manufactured?

A: Yes, we can custom make any make or model of valve, however a minimum run of 50 of each valve would be required for custom manufacturing.

----

Q: What is the hardness of the Nitride layer on the valves?

A: The Nitrided Valve hardness is about 800 Vickers = equivalent to 52 Rc (equivalent because is just a thin layer.

----

Q: What are the operating temperatures of the valves?

A: Our stainless valve has a 1,460 F. (approx 1900 F EGT) The INCONEL valves have 1,600 F (approx 2200 F EGT)

----

Q: What is the durability of our Titanium valves?

A: Depends on many factors like operating temp., seat hardness, rpms, etc. but a reasonable number are 1000 miles in racing applications

----

Q: What is the piston to Cylinder wall clearance?

A: All our pistons come with a specification sheet, please read that sheet carefully. Piston diameter must be measured at the gauge point indicated on the sheet. Required clearence depends on the diameter, alloy, type or forging (full Skirt or Slipper design) application, operation conditions.

----

Q: What is the clearence between the Connecting Rod and the Wrist pin?

A: The clearence between Rod and Writs pin is 0.010-0.012mm (0.0004"-0.0005")

----

Q: What is the difference between 4032 alloy and 2618 alloy?

A: A) 4032 High Silicon (aprox. 11% of Silicon but enhanced with additional Copper, Nickel & Magnesium) Low expansion alloy.
B) 2618 Low Silicon High Expansion alloy. Because most use the 2618 they say it is better, but that is not always like that. In fact they are pretty similar and the difference is not that big

----

Q: What is the Expansion rate of 4032 alloy:

A: 4032 expands 18% less than 2618

----

Q: What should the clearence be between the Piston dome and Cylinder head?
A: For Steel rods: 0.040” (1mm). For Aluminum rods: 0.060” (1.5mm).

Gebruikers-avatar
devers
HCN Newbie
HCN Newbie
 
Berichten: 59
Geregistreerd:
06 Jan 2013, 23:27
Woonplaats:
Gendt

Re: project honda civic turbo

Berichtdoor speeddevil » 15 Apr 2014, 13:59

NICE, bijna elke dag meegereden/ gereden toen die nog van bigsach was.
echt een monster van een auto.
en mooi om te zien dat ie nu weer opgebouwd wordt :drive2: !

Gebruikers-avatar
speeddevil
HCN Regular
HCN Regular
 
Berichten: 294
Geregistreerd:
16 Jun 2008, 22:00

Re: project honda civic turbo

Berichtdoor cupra3382 » 13 Sep 2019, 12:16

Zo een tijdje weg geweest en een hoop tegenslagen gehad en nu 2 weken geleden een andere auto gekocht om eindelijk weer eens na zoveel jaren te gaan sprinten en dragracen.

https://www.flickr.com/photos/184397261 ... ed-public/
https://www.flickr.com/photos/184397261 ... ed-public/
https://www.flickr.com/photos/184397261 ... ed-public/

cupra3382
HCN Regular
HCN Regular
 
Berichten: 137
Geregistreerd:
28 Jul 2011, 00:20
Woonplaats:
Maastricht

Re: project honda civic turbo

Berichtdoor mielko » 13 Sep 2019, 18:36

Dat was zeker lang geleden dat jij gereageerd hebt. Welkom terug
Afbeelding

Gebruikers-avatar
mielko
HCN Regular
HCN Regular
 
Berichten: 1403
Geregistreerd:
09 Mrt 2005, 18:15
Woonplaats:
Ja ik maak spel fouten,maar ik kan tenminste iets met mn handen bouwen

Re: project honda civic turbo

Berichtdoor cupra3382 » 14 Sep 2019, 22:24

bedankt :up:

cupra3382
HCN Regular
HCN Regular
 
Berichten: 137
Geregistreerd:
28 Jul 2011, 00:20
Woonplaats:
Maastricht

Re: project honda civic turbo

Berichtdoor Kevinio » 16 Sep 2019, 09:41

Nice! Ziet er tof uit, wat zijn de specs?
Wil je upgraden van kansloze 'spoon feeder' naar gerespecteerd forumgebruiker, gebruik eens de zoek-functie! :oops:

Gebruikers-avatar
Kevinio
HCN Crew
HCN Crew
 
Berichten: 9667
Geregistreerd:
22 Mei 2007, 14:27
Woonplaats:
Helmond

Re: project honda civic turbo

Berichtdoor cupra3382 » 22 Sep 2019, 19:28

81,5mm
Cp zuigers
Eagle drijfstangen
Acl race lagers
Arp kopbouten
Competition stage 4 koppeling
Bwr ramhorn header
Gt3076r turbo
Supertech klepveren + schotels
Supertech klepseals
Edelbrock victor x
Hondata 4 bar mapsensor
S4c aangepast
Tial wastegate
Tial blowoff
3 inch voor naar achter uitlaatlijn

Onderstel
282 remmerij voor
Ebc schijven en ferode blokken
Ek9 swaybar voor
Pu masterkit rondom
D1spec schroefset
Skunk2 draagarmen (echte)
Stalen remleiding rondom
282 achterremmem
Ebc schijven en ferode blokken achter
Summit achter strutbar
Strutbar voor

cupra3382
HCN Regular
HCN Regular
 
Berichten: 137
Geregistreerd:
28 Jul 2011, 00:20
Woonplaats:
Maastricht

Re: project honda civic turbo

Berichtdoor cupra3382 » 11 Feb 2020, 20:27

Afbeelding

cupra3382
HCN Regular
HCN Regular
 
Berichten: 137
Geregistreerd:
28 Jul 2011, 00:20
Woonplaats:
Maastricht

Re: project honda civic turbo

Berichtdoor B00ster » 11 Feb 2020, 23:20

En schiet het al op of word het toch 2021?
Afbeelding
If everything seems under control, you're not going fast enough!!!
- Civic EJ2 H22 topic- CRZ- Airbrush-2nd Urban Tuning Fest

Gebruikers-avatar
B00ster
HCN Groupie
HCN Groupie
 
Berichten: 7857
Geregistreerd:
13 Feb 2009, 21:28
Woonplaats:
Limburg

Re: project honda civic turbo

Berichtdoor cupra3382 » 12 Feb 2020, 00:10

Ik moet nog een paar kleine dingen doen aan de civic.
maar ik wil dit jaar zeker naar evenementen gaan.

cupra3382
HCN Regular
HCN Regular
 
Berichten: 137
Geregistreerd:
28 Jul 2011, 00:20
Woonplaats:
Maastricht

Vorige

Terug naar Projecten



Wie is er online?
Gebruikers in dit forum: Geen geregistreerde gebruikers en 41 gasten
cron